Jump to content


Photo

FWC Fishing Rod Holder

Hawk

  • Please log in to reply
6 replies to this topic

#1 SD_Beaker

SD_Beaker

    Member

  • Members
  • PipPip
  • 22 posts
  • LocationSan Diego

Posted 04 July 2018 - 05:54 PM

Here's the fishing rod holder I put together for my trout rods in my FWC-Hawk.  It will be held on via screws and wingnuts in the storage holders (so clamp is only temporary).  Have not used it yet, but I had a similar setup in my last Pop-Up (Northstar TC650) which worked well.

Attached Thumbnails

  • 20180704_Hawk Rod Holder_004.JPG
  • 20180704_Hawk Rod Holder_002.JPG
  • 20180704_Hawk Rod Holder_005.JPG
  • 20180704_Hawk Rod Holder_006.JPG
  • 20180704_Hawk Rod Holder_007.JPG

  • 0

#2 Wandering Sagebrush

Wandering Sagebrush

    Free Range Human

  • Site Team
  • 6,059 posts
  • LocationNorthern Oregon

Posted 04 July 2018 - 07:50 PM

Nice!
  • 0
Real Dogs Have Beards - Fear the Beard

Tu Ne Cede Malis

#3 TrapperMike

TrapperMike

    Advanced Member

  • Members
  • PipPipPip
  • 59 posts
  • LocationNW Wisconsin

Posted 07 July 2018 - 02:22 AM

SD_Beaker:   I like that.  My rod holder/case is on the exteriore under the overhang.  4" PVC, but could have went as large as 6".  Held on by SS footman loops and SS hose clamps.

 
gallery_6242_1230_71028.jpg
 
 
gallery_6242_1230_97144.jpg

  • 0

2016 FWC Hawk Shell

2011 Chev Silverado 1500 4x4 ext cab

2018 Chev Silverado 2500 4x4 ext cab 

Super Springs

Helwig Sway Bar


#4 Ronin

Ronin

    Senior Member

  • Members
  • 532 posts
  • LocationGrass Valley, CA

Posted 15 August 2018 - 03:38 PM

 

SD_Beaker:   I like that.  My rod holder/case is on the exteriore under the overhang.  4" PVC, but could have went as large as 6".  Held on by SS footman loops and SS hose clamps.

 
gallery_6242_1230_71028.jpg
 
 
gallery_6242_1230_97144.jpg

 

Trapper Mike:

 

Finally getting around to installing a 6" conduit storage tube under the roof of my Hawk. Where did you put the footman loops? Are the loops against the front panel just below the corner where it meets the roof? Anything you would have done differently??

 

Thanks!!


  • 0

#5 TrapperMike

TrapperMike

    Advanced Member

  • Members
  • PipPipPip
  • 59 posts
  • LocationNW Wisconsin

Posted 15 August 2018 - 07:58 PM

Ronin,

The footman loops are tight to the corner intersection of the overhang and front wall, but are attached to the metal on the vertical surface of the front wall.  There is a beam behind there and just used stainless strews.  So far so good and everything is holding up well.

Mike


  • 0

2016 FWC Hawk Shell

2011 Chev Silverado 1500 4x4 ext cab

2018 Chev Silverado 2500 4x4 ext cab 

Super Springs

Helwig Sway Bar


#6 CougarCouple

CougarCouple

    Senior Member

  • Members
  • 1,123 posts
  • LocationLas Vegas

Posted 16 August 2018 - 12:50 AM

Saw this today IMG_1278.JPG

Russ
  • 0
F250 extended cab, Cougar from ATC. You guys rock thank you!

#7 Ronin

Ronin

    Senior Member

  • Members
  • 532 posts
  • LocationGrass Valley, CA

Posted 16 August 2018 - 04:01 PM

Ronin,

The footman loops are tight to the corner intersection of the overhang and front wall, but are attached to the metal on the vertical surface of the front wall.  There is a beam behind there and just used stainless strews.  So far so good and everything is holding up well.

Mike

Thanks!! I should receive my conduit carrier kit today. The Buyers 6"conduit kit price was recently reduced to $38.00 so I decided to go for it. Just one of those "I'll get around to it someday mods".


  • 0





Also tagged with one or more of these keywords: Hawk

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users