Thanks for posting your project. It is fun to follow along.
This old Granby build
#11
Posted 27 June 2015 - 03:00 PM
#12
Posted 28 June 2015 - 02:20 AM
#13
Posted 28 June 2015 - 02:29 AM
#15
Posted 30 June 2015 - 05:46 AM
Looks like you are doing a great job!
#16
Posted 01 July 2015 - 04:21 PM
Nice project, excellent work. A vintage camper on a vintage truck, bonus points that your camper went through another "customer" before coming back home. Thanks for posting.
#17
Posted 04 July 2015 - 01:47 AM
Awe A pucker,I moved it to the garage today to get the liner and roof in place and I got a pucker.My home made liner that seemed to fit so well before I cut and sewed the windows now a has pucker.If I could just sew this probably would have never happened.The sides look Okay
Not sure what to do but I did find out one thing,I should've had it in the garage the whole time,once I got it level things like door now stick,don't know about the roof yet but I'm anticipating problems.As far as the pucker goes I may put it like FWC had it with the liner over the roof instead of pulling the staples and bending the alum and putting it under so when I save some money I'll buy one from Marty and do it right.I really wanted to get this in traveling shape by the third week of July..
#18
Posted 04 July 2015 - 03:03 AM
That doesn't look that bad. I think it'll be okay.
Craig K6JGV_________________________ 2004 2500 CTD 4X4 FWC HAWK 1960 CJ5
#19
Posted 04 July 2015 - 06:10 AM
I would divide the pucker into either two, three or four puckers and position them over a larger area.
I would also move the puckers away from the corners.
The pucker should be oriented so that it sheds air and water to the rear of the camper to achieve a shingle affect. The pucker in the posted picture is oriented incorrectly.
This is how I would do it:
Determine the size of the pucker.
Mark the leading edge of the pucker.
Mark the Side Curtain where the leading edge contacts it.
Remove the Side Curtain.
Open up the pucker and measure between the two marks. This is the width of the pucker.
Divide this measurement by 2, 3, and 4.
These measurements will be referred to as Width 2, Width 3 and Width 4.
Using 3x5 cards to practice making a pucker and determine the best number of puckers to use.
Along the 5" side mark Width 2.
Fold the two marks to each other to form a pucker half as wide as the original pucker.
Repeat using Width 3 and Width 4 measurements.
Assuming there is a center back seam:
Fold the Curtain in half along the Center Back seam, inside to inside.
On the outside:
Mark Center Front.
Fold Center Front to Center Back.
Mark Center Left.
Mark Center Right.
On the camper:
Determine the perimeter.
Mark Center Front.
Mark Center Back.
Mark Center Right.
Mark Center Left.
Attach Side Curtain to camper only at Center Front and Center Rear.
Double sided tape works well for this.
Locating The Puckers:
From the picture posted it looks like the pucker is not very wide and dividing it into two puckers would be satisfactory. If not use three or four.
I would not locate the puckers on the camper front leading edge.
If locating on the right side, left side or rear side avoid the corners and windows.
Right and Left Side Puckers:
Mark Width 2 on Right Side Curtain at Curtain Right Center.
Fold curtain to form pucker and align Curtain Center Right and Camper Center Right.
Double sided tape works well for this.
Mark Width 2 on Left Side Curtain at Curtain Left Center.
Fold curtain to form pucker and align Curtain Center Left and Camper Center Left.
Rear Puckers:
On camper Rear Side mark an equal distance to the right and left of Center Rear to establish Right Rear Pucker location and Left Rear Pucker location.
On Side Curtain mark the same equal distance to the right and left of Center Rear to establish Curtain Right Rear Pucker location and Curtain Left Rear Pucker location.
Mark Width 2 at above pucker locations.
Fold curtain to form pucker and align Camper and Curtain Right Rear Pucker and Left Rear Pucker marks.
Another Way To Do It:
Remove the pucker at the Side Curtain Center Back Seam.
You said that you can't sew, but I know that you can.
Sewing is one of the first and most basic of all human activities.
A little seven year old Bagladeshi girl could do this.
Purchase a stitching awl with the hole at the point of the needle.
Read and follow the directions, practice sewing 3x5 cards together.
How To Do It:
Divide the Pucker Width in half.
Mark a line parallel to the Curtain Center Back Seam equal to this quotient. This new Center Back Seam will increase the width of the seam allowance.
If the Curtain Center Back seam allowance is stitched down, it will need to be unstitched.
Stitch new Center Back Seam.
Simple.
You can do it.
#20
Posted 04 July 2015 - 07:32 AM
Just read the thread from the beginning and see that you did a great job of sewing it. I was right!
It would be a good idea to restitch it with a #69 or #92 bonded polyester with uv inhibitors.
Probably not what you want to hear. But the regular home sewing thread is not up to the task.
These size threads are too big for a home machine so it would have to done with a needle and awl.
With the curtain already assembled it would be a lot easier than if it wasn't.
It could be hung vertically and stitched while standing or sitting.
SailRite has the thread and stitching awl.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users