Jump to content


Photo
- - - - -

Another table design

table

  • Please log in to reply
3 replies to this topic

#1 Laguna-to-Crestone

Laguna-to-Crestone

    Newbie

  • Members
  • Pip
  • 9 posts
  • LocationLaguna Beach, CA / Crestone, CO

Posted 11 September 2016 - 11:09 PM

I thought I would share my new table for my Ocelot with roll-over couch.  I mounted the table on the cabinet in front of the water tank using oak mounts that allow the sliding cabinet door to slide behind them.  The table sits on folding shelf brackets.  I added a couple of braces to the inside of the cabinet - a piece of 1.5" X 3/4" wood that ties the front of the cabinet to the back that I accessed through the drawer opening and an angle iron inside the cabinet.  

 

The table is 18" X 32" and made of 3/4" oak plywood.

Attached Thumbnails

  • DSC00591.jpg
  • DSC00587.jpg
  • DSC00593.jpg
  • DSC00592.jpg

  • 0

#2 ski3pin

ski3pin

    Belay On

  • Site Team
  • 14,286 posts
  • LocationSierra Nevada Range

Posted 11 September 2016 - 11:34 PM

Looks like a nice sturdy design! Thanks for posting.


  • 0

2003 Ford Ranger FX4 Level II 2013 ATC Bobcat SE "And in the end, it's not the years in your life that count. It's the life in your years."- Abraham Lincoln  http://ski3pin.blogspot.com/


#3 carld

carld

    Senior Member

  • Members
  • 179 posts
  • LocationDecatur Texas

Posted 18 September 2016 - 03:35 AM

Hay, it's just like my table but improvement. My table mounts to the top rail of the sliding door, but is a little high. You added two right angle braces so you can lower the table to a normal hight. A little more work but it looks good. So maybe it time to do some modifications.   Great job. 

 

I just used a simple hinge to mount the table.  Then I  used a 6 x 10 x 1/8"brace  to the lower slider rail that held it up.  So when folded down it is flush to the original cabinets.  Then I put a magnetic cabinet latch to hold it in place when down.  The shelf brackets don't let the table fold down flush to the cabinets. 

 

I used 1/2" ash plywood for the table and rounded the corner.  You can add 3/4" molding to the outside and sand it cut/sand it down to 1/2".  Steam the trim for 30 min at to fold it around the corner. 

 

Note the extra board on the bottom of the shelf.  This is for storing the brace. I cut a 1/4" groove in the table holding brace and extra board to allow the brace to slide into when down.  

 

I've used the original and my new design and the new one is much better.  Great improvement!

Attached Thumbnails

  • Table_support.jpg
  • Table_up.jpg

Edited by carld, 18 September 2016 - 03:59 AM.

  • 0

2002 Tundra AC 4x4 with 2015 Ocelot

2006 Tundra AC 4x4 with 2018 78" Ocelot

2011 Tundra AC 4x4 with 2010 78" Ocelot

 

 


#4 Laguna-to-Crestone

Laguna-to-Crestone

    Newbie

  • Members
  • Pip
  • 9 posts
  • LocationLaguna Beach, CA / Crestone, CO

Posted 22 September 2016 - 09:05 PM

Thanks Carl - and I should have credited you with the inspiration.  I set out to copy yours and ended up with my design to address the height issue.


  • 0





Also tagged with one or more of these keywords: table

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users